Do you need to distribute the Internet to several devices or create a small network to exchange data, but don’t have a router or switch at hand?
This problem can be solved with only a laptop with a Wi-Fi adapter installed.
As you know, devices in Wi-Fi networks can operate in two modes:
- Ad-Hoc mode (point-to-point) - in this case, clients interact directly, bypassing intermediaries.
- Infrastructure mode (client-server) - in this case, interaction between network hosts occurs exclusively through an intermediary - an access point.
Theoretically, the simultaneous operation of one Wi-Fi adapter in two modes is impossible, just like the simultaneous operation of several operating systems on one host.
After starting the virtual AP, the built-in DHCP server is activated.
In order for client devices to be able to visit Internet resources, you should go to the menu “ Network connections» RMB click on the adapter through which you connect to the Internet.
In our example, this is a wireless adapter, go to the “Access” tab and check 2 checkboxes in the appropriate fields:
To disable use the command:
netsh wlan stop hostednetwork
To deactivate the access point, enter:
netsh wlan set hostednetwork mode=disallow
Using Virtual AP organized by built-in using Windows carries a number of limitations: creating only one virtual adapter, which only works in access point mode.
The maximum number of wireless client devices operating in the network is 100.
Creating a Virtual AP using third-party programs
For those who don't want to configure Virtual AP using the command line, there are many shell programs that make setting up Virtual AP easy with a graphical interface.
Unlike an access point created from the command line, an access point created using the utility does not require activation after turning on the computer, and its configuration is quite trivial.
For example, using the free Virtual applications Router Manager for deployment wired network takes less than 1 minute.
It is enough to indicate in the SSID field - the name of the wireless network, Password - the password for connection, Shared Connection - the interface on the basis of which the Virtual AP will be created, and then click the “Start Virtual Router” button.
How to make a laptop a wi-fi hotspot
Laptop as a point Wi-Fi access - complete instructions on setting up the adapter
Some office router models can operate in one of two modes, the “router” itself and the “access point”. IN this review– Let’s take a closer look at how to configure a router as an access point. At the same time, we will consider how these two modes differ, and when exactly it is necessary to turn on the second of them.
Most users know what a “router” is. An even simpler device is a switch. But switches are only wired. Now imagine that the cable ports of the switch were combined with a wireless network. A device that provides this capability is called an “access point.” We can say that the access point is a “wireless switch”.
Access point connection diagram
There is no need to configure the cable switch, and in the access point settings you only need to specify the name of the Wi-Fi network and the operating mode of the radio channel (also, the encryption mode, if required). We will talk about how to make an “access point” from a router, that is, a “more complex” device.
Switching the router to AP (Access Point) mode
How to switch a D-Link router to AP mode
Note that this feature (that is, the presence of an “access point” mode) is not present in all routers. But in some hardware revisions of the D-Link dir-300 it is provided.
What is different about a router operating in this mode? All wired ports (including WAN) are connected to a common switch. The Wi-Fi network, in turn, is integrated with the latter’s network.
Before switching the router to “AP” mode, it is still better to fully configure the wireless network. To do this, go to the “Setup” -> “Wireless Setup” tab and click “Manual Wireless...”:
Setting up a Wi-Fi network
Here everything looks standard: set the SSID value, select the radio channel number (or turn on “automation”). Finally, click “Save Settings”. If you need to set up encryption, do it right away (using the capabilities of the “Wireless Security Mode” block).
But you can enable the “Access Point” mode on another tab. It's called "Internet Setup":
Enabling AP mode (D-Link router)
To activate the required mode, check the “Enable...” checkbox and save the changes made.
Additionally, before enabling the “AP” mode, we recommend that you make sure that you can connect to the configured wireless network.
Happy setup!
How to switch ASUS router to AP mode
Review the information discussed in the previous chapter. The sequence of actions is the same for routers from all companies: set up a Wi-Fi network, check its functionality, and turn on the “Access Point” mode.
You can do the latter in the ASUS router on the “Administration” -> “Operation Mode” tab:
Enabling AP mode (ASUS router)
Place the selector opposite the inscription “Access Point”, click “Apply”.
How to get a "hotspot" without turning on AP mode
Features of the “second method”
Any router can be used as an “access point”. It configures a wireless network, and then disables the DHCP server (and the UPnP option, if it was enabled).
After this, we will get a “switch” with four wired ports (without a WAN port). And also, with the network of this switch it will be combined wireless network. The latter is true if you do not check the “AP Isolated” checkbox when performing the setup (but by default, this is the case).
We can say that the result of the second method is worse in that the user will receive one less wired port. The WAN connector after configuration is not used.
An example of setting up an “access point” based on a D-Link router
First, we set up a Wi-Fi network. Then, go to the “Setup” -> “LAN Setup” tab to uncheck “DHCP Server”:
Setting up a DHCP server
In the second step, turn off UPnP (tab “Advanced” -> “Advanced Network”):
Disabling UPnP
Do not forget to save the changes made (which is done on each tab). The resulting device is a 4-port switch with an access point built into it.
Happy routing!
Problem common to both methods
By connecting the newly acquired “access point” to the router, you can lose access to each of the devices:
Local IP addresses of devices
This is possible when the access point’s own IP is within the range of local addresses of the router (modem/router). The problem is easily solved. You must first change the IP of either the router itself or the access point.
Let the router address end with the numbers 1.1. Then, set the IP of the second device to 192.168.2.1 (or 192.168.0.1 is possible). The point is that the IP values should be from different subnets.
To do the latter (in D-Link routers):
- Go to the “Setup” -> “LAN Setup” tab
- Change the value of “Router IP Address”
- Saving the settings
In the new D-Link interface, it looks a little different (“Network” -> “Connections” -> double click on the “LAN” line):
Change IP (D-Link router configured as an “access point”)
Actually, no other problems were found.
Many users who, in addition to desktop computer there are various portable devices(laptops, small netbooks, tablets, smartphones, etc.) supporting wireless connection, want to create an access point. This is very convenient, since all of the above devices can work simultaneously and without any cords.
So today we'll talk about access point. I'll tell you how this is done on computers that have Piggy (XP) installed. So, first you need to make sure that your device is equipped with wireless adapter. To find out, launch the start menu, from where go to the control panel. Select the section to display all yours. If you see what interests us, then read on to learn how to set up an access point. If not, then connect the necessary equipment, otherwise everything further actions will be meaningless.
Next, click on the local connection with the right key of the manipulator and select the properties item. There, go to the section called Internet Protocol or TCP\IP and launch its properties. Enter the IP address 192.168.0.1, and - 255.255.255.0. Confirm these settings. Then you need to turn on your router and wait a few minutes. Next, you need to go to its settings through the browser. Depending on the model, this is done differently, see the instructions.
Now about how in the browser. Select section quick settings and click "Next". Enter the name of the network (I advise you to remember it or write it down on paper) and the password for access (you should also write it down). Then in the channel field, select any value available to you, click “Next” again. If necessary, you must indicate the login and password that you received from your provider. After this, you should save the settings and restart the router.
We wait for the router to reboot and try to connect to check if you were able to configure the access point. Find yours in the list of available networks, the name of which was written down, and connect to it. When asked to enter a key, indicate the one that you also have written down. That's it, now we wait for the device to identify the connection and report it.
If everything is fine, an icon in the form of a small monitor will appear in the tray. There should not be any on it. If there are any, it means that something went wrong. If everything is fine, launch your Internet browser and try opening different pages. Connection and setup are considered complete when all sites open in your browser without problems.
If this does not happen, check that all settings have been entered correctly. If yes, then contact your provider. Perhaps in at the moment He doesn't have an internet connection.
Now you know how to configure an access point. There is absolutely nothing complicated about this, the main thing is to do everything correctly and according to the manual that comes with your router.
Installing and configuring a wireless access point that will connect to your existing wireless network can be a little tricky. In the following article, the various steps required for an access point setup are divided into broad categories and in a list. For broadcasting or extending the range of a wireless network or allowing a wired network to wirelessly broadcast, one piece network equipment A wireless access point (WAP) is also used. Below is detailed description on setting up a wireless access point for your home network.
How to install a wireless access point
Instructions - how to set up a wireless access point:
Network information
Your WAP acts as an intermediary between the device, between the router and the computer, and tries to connect to your home network. Therefore, your WAP must be entered into the wireless settings of your router so that the wireless access point picks up and transmits the correct signal. Before you do anything with an access point, you will need the following information from the router:
Router IP address
DHCP address range
Wireless:
Wireless network name SSID
What wireless channel is being used?
Security mode (WEP, WPA, etc.)
Password or security key (copy all parameters such as number of keys, encryption, etc. to be safe)
Please write down the above information correctly. Minor changes to the settings and nothing will work. To get this information, you will need to go to the router's settings page. If you are familiar with the process or know the settings, skip the following steps:
I. Using any computer, get hard wired access to the router. Do not connect to your wireless router page.
II.Open Command Prompt and in a black screen, enter the ipconfig command.
III. Look in the Default Gateway field. An example of what this might look like is: “192.168.1.1”. Write down this is the IP address of your router.
IV. Close the command prompt window, and open any web browser. Delete any URL in the address bar and enter your router's IP address. Press Enter.
V. A dialog box will appear asking for your router's login and password (not associated with a wireless network). If you have any opportunity, please enter it now. The default login for most routers is an empty username and administrator password. Click on Ok.
VI. In the main screen of the setup program, look for DHCP-Range and DHCP start and end addresses. Write it down.
VII. Now look for the tab at the top of the screen that says Wireless or Wireless Network Settings. Click on the tab, there may be sub-tabs such as basic setup, security and advanced. Look for the wireless network data and information above (SSID, security, etc.) and write it down.
VIII. Check if you have network name broadcasting enabled, i.e. your network name has been seen and connected, select it. This parameter is usually called SSID broadcast and is located in the wireless settings page.
WAP connection
1.Now it's time to deal with this access point. Connect the Ethernet cable to the port on the WAP, and the other end of the wire to the Ethernet port of your computer, so that the WAP and the computer are connected together. Turn on the access point.
2.Open Command Prompt and enter ipconfig /renew. Then enter ipconfig. Look for the Default Gateway address, currently the WAP address that needs to be changed.
3.Open a web browser and enter this address in the address bar. Login to the page (username is blank, password: admin) and you are now taken to the WAP installation page.
4.The default mode for the operation of the Access Point in most routers. If such a specification is on the WAP settings pages, make sure that only the Access Point mode is set.
5.The first IP address of the router must be assigned. Look at the IP address term and there should be four filled boxes next to it.
6.To better understand what an access point address is, the address should be like this - an example:
Let's assume that your router IP address is 192.168.1.1 and the DHCP start address and end address are 192.168.1.10 - 192.168.1.15
7. Since the DHCP range is 10-15, the access point address should not be any of these numbers, it should be something else. The ideal address for the access point is 192.168.1.2. That is, within the router's subnet range, but not within the DHCP range. Enter this type into the IP address field. Do not enter the Default Gateway field.
8.Look at any option that says DHCP enabled and possibly a checkbox or “yes/no”. Disable DHCP. With this change in address, the web browser may attempt to refresh or a message may be displayed. Close all windows.
Setting up a wireless network
10.Creating a WAP address, now the physical connection must be changed. Connect the router or local network Ethernet port to port on WAP. Connect another cable between the computer and the port router. Apply power to the access point. Now your computer and WAP are connected, but not to each other, instead the router is working.
11.Now on your computer, open a web browser and enter the WAP IP address that was just assigned (in this case, 192.168.1.2) and enter the settings page. Look on the main tab to see what it says Wireless.
12.In this tab, enter the SSID and wireless channel. Look for the sub-tabs that say Wireless Security and click on it. As part of this, select the correct security settings and enter the password or key that is used for your network. This step is to enter the wireless router settings on your access point. After that, close your browser.
13.The LEDs on the access point should be working. Check the WAP manually to see if they are lit correctly - WAP. If you are connecting to a wired router, leave the connections as they are for now. If you have a wireless router, then you can unplug the WAP from the router and install it in a location, such as where it picks up the router's signal and transmits it Right. This process has a bit of "trial and error" in nature, as you must test the signal strength to place the wireless access point at the optimal location.
The above WAP installation procedures may seem very tedious, but you just have to be patient and read the instructions carefully before doing anything. Keep in mind that the access point is now configured with your router's wireless setup software, so if you don't change them to the router, you must change them to the access point.
This article will help answer the following questions: how to set up an access point, how to set up a router and will bring clarity. According to Wi-Fi equipment manufacturers, setting up a wireless network (WLAN - Wireless Local Area Network) is a matter of minutes. Press the button and the device connects. In reality, Wi-Fi routers confuse even experienced PC users. Most are glad that the signal occurs at all - they usually forget about reliability. In this article, you will learn how to set up a Wi-Fi access point, how to set up a Wi-Fi router, and how to make your wireless connection reliable to protect your network from unwanted guests.
I want to say right away that new detailed material has appeared on setting up the router:. I recommend using it first for setup wi-fi router A.
Which Wi-Fi router or access point to choose?
Choosing a Wi-Fi router. The stumbling block for multimedia transmission is always the Wi-Fi standard. You can quickly transfer large files or watch HD videos over a wireless network only if it complies with the 802.11n standard, which supports speeds of up to 300 Mbps. I also advise you to read about the new wireless network standard - in order to buy a device with a reserve for the future. If this is not necessary, then choose any router from a well-known manufacturer ( D-Link, TP-Link, Asus or Netgear), which comply with the 802.11n standard - this is more than enough for any high-speed Internet connection.
Wi-Fi adapters. Users who use modern laptops or PCs with an integrated wireless network adapter do not need additional equipment, but owners of older laptops need to take care Wi-Fi modules on the USB bus or Wi-Fi Card-Bus adapters.
How to locate a Wi-Fi access point or Wi-Fi router
All three network Wi-Fi standard usually operate at 2.4 GHz. In this regard, several problems arise at once. One of them comes down to the fact that in this frequency range Not only Wi-Fi equipment works. For example, microwave ovens, cordless telephones and wireless interface extenders also use this frequency, which increases the level of interference. Another problem is related to the signal transmission environment: the human body and reinforced concrete structures degrade the quality of the signal if they are located along its path. In order for the signal to be available throughout the entire room, it is important to choose the right location. The connection works best if the router is mounted as high on the wall as possible. In addition, the router should not be located directly next to a computer or other device that emits strong radiation or interferes with radio waves due to metal case. Proper placement of the router's antennas is also critical. In most cases, you can get more coverage if you aim them vertically.
Connecting and setting up a Wi-Fi router (access point) for a local (internal) network
Connect the computer and the router with a network cable (use sockets for the external network; there are usually 3-5 of them, they are located side by side and labeled. Make sure that you have established a connection between the computer and your wi-fi router (the connection icon in the taskbar tray lights up) .
- IP address: 192.168.0.2
- Subnet mask: 255.255.255.0
- Default Gateway: 192.168.0.1
- DNS: 192.168.0.1
If you find other parameters in the manual, set them. Open command prompt ( Start - Run- in the window that opens, write “cmd” for Windows XP or click Start and enter “cmd” in the search bar). Next in the opened command line write: ping 192.168.0.1 . If packets arrive from 192.168.0.1, then you did everything correctly. If there is no response and we see messages about exceeding the waiting limit, it is worth trying to change IP 192.168.0.1 and 192.168.0.2 to 192.168.1.1 and 192.168.1.2, respectively, and then try to “ping” the address – 192.168.1.1 If you If you still fail, then consult the manual to understand what IP address the router accepts on the internal interface.
I also recommend checking again whether the network cable on the router is plugged into the right socket, and whether a crossover cable is being used. IN manual for wi-fi connection router it should be written how to get into the web interface to manage the router; if you cannot find this section or the manual itself is missing, you should check the addresses http://192.168.1.1 or 192.168.0.1 , depending on which address we were able to ping. in your computer's browser. If you have already tried to connect the router, then you need to first reset the settings with the button "Reset" on the back panel. It’s also worth checking the same addresses but with a secure protocol https://, instead of http://
On the page that opens, you will be asked to enter your login and password. If nothing is indicated in the instructions for connecting a wi-fi router, then you should try the admin/admin or admin/password pair - these are the most common pairs and they are found in almost all popular router models. After entering the administration mode, select the Russian language in the interface settings section so that everything becomes intuitive if it is present.
Most often, Wi-Fi routers allow packet forwarding in the internal network interface, so you can already turn on additional PCs and connect them through other sockets for the internal network, and start using the internal network.
How to set up a Wi-Fi router
We will look at how to enter data to access an Internet connection below, using the example of one of the Wi-Fi routers, but for now let’s go to the “Wireless Settings” settings section ( setting up a wireless network) or to the section “Wi Fi”, “Wireless”, etc.
Now give your name home Wi-Fi network in “Name (SSID)”. Under this name, the wireless network will appear in the list of available networks on the other device. Select your region (Europe - the American installation has a longer range, which, however, is prohibited here). In the “Channel” column, set the value to “Auto” - then the Wi-Fi router will analyze the air and use the channel with the least amount of interference. Confirm the settings by clicking on “Apply”.
Wireless Security
The network is installed, now it’s a matter of choosing protection. Without a strong password, anyone can access the Internet through your connection. There are three main encryption methods for protecting a Wi-Fi network: WEP, WPA and WPA2. All of them are vulnerable to one degree or another, but with my help your network will be quite reliably protected from hackers. Encryption using WEP is extremely unreliable - we recommend not using it. WPA (Wi-Fi Protected Access) encryption, which is based on the AES encryption method, is quite secure and difficult to crack. To select the keys, a hacker will need many years or a computer that is orders of magnitude faster than current PCs in speed.
WPA2 offers better security. True, hackers were able to find a loophole here, but the costs of hacking are too high. However, all these security methods require a dedicated authorization server (RADIUS), which is not applicable in a home or small office network. They are encrypted using WPA and WPA2 with predefined keys. To use them, on the “Wireless Settings” tab, activate “WPA-PSK (TKIP)” or “WPA2-PSK (AES)”. When prompted for “Security Encryption”, specify a password - it is not recommended to use less than 15 characters for it. Confirm your entry by clicking “Apply”.
Optional Wi-Fi router setup
Each network device is equipped with its own network address MAC (Media Access Control). In the router you should register the addresses of only devices known to you - others should not have access to the router. To do this, click in the “Advanced” menu item on the “Wireless Settings” tab and select “Setup Access List”. After this you will receive a list of connected devices. Find out the MAC address of the wifi module on a laptop or wifi network card on a PC it’s simple - in the command line type “ ipconfig /all” Select the computers for which you want to open free access, and click on “Add”. Now check the box next to “Turn Access Control On”, click “Apply” - and the network protected from hackers is ready. Don't forget that it's best to do all this after you've set up a wireless connection on your client computers.
Restart the Wi-Fi router via the web interface and try setting up a network on your device using the following settings:
IP– from the range of free addresses
Mask – 255.255.255.0
Getway – 192.168.(0-1).1
Setting up the Internet on a Wi-Fi router or setting up an external network
If we need to distribute the Internet via the internal network, we need to connect the network cable with the “Internet” to the external interface on the wi-fi router (the external interface is usually located slightly away from the others and is signed accordingly WAN)
Then in the router settings you need to specify the settings external interface your provider: they are usually included in the contract, or call technical support. You should also not forget about DNS - the router probably has a caching DNS server or, as a last resort, a DNS tunnel, configure it. It is also worth checking whether the exchange of packets between interfaces is allowed; if so, then the Internet most likely already exists on your internal network.
By the way, I would like to note that the latest models of wi-fi routers and some of the previous ones (Asus, for example) have the ability to work with the PPPoE protocol - which has recently become more and more common among providers, so at the end of the article you will find a step-by-step instructions for setting up a Wi-Fi router with a connection via the PPPoE protocol . If your Internet is like this, then make sure that you have a router that supports PPPoE. Here I have described the main types of Internet connections so that you can determine yours.
Gh34EwF-MB4
P.S. Let me remind you once again about the “cherished button” that answers the question “ How to reset a password on a router, if I forgot the old one.” Each router has a “Reset” button - after clicking on it while the router is running, it reboots and all settings are set to their original settings.
Setting up a wi-fi router. Troubleshooting Wi-Fi Networks
Why doesn't Wi-Fi want to transfer data? You connect to Wi-Fi, but the browser cannot display the site. Let's find ways to solve this WLAN problem:
Weak Wi-Fi connection signal. Sometimes WLAN transmits data one and a half, two times slower and the signal is always bad, regardless of the location of the antenna. Reason: Your network is overlapped by another WLAN that operates on the same frequency. To allow multiple radio networks to exist side by side without overlapping each other, the 802.11b/g standard provides 13 channels at 2.4 GHz. Many routers are configured for channels eleven or six. With free app NetStumbler you can find and recognize neighboring WLANs and find out which channels they operate on. Download the app from the official website and start searching. After this, you will see the channels of the networks around you. Now, through the router's web configuration, set your WLAN to one of the channels that is not used on this network and check if the signal has improved.
How to increase the range of a Wi-Fi network. If the range of the Wi-Fi router is insufficient, it is usually used WDS technology(Wireless Distribution System - distributed wireless system). It allows Wi-Fi access points to establish connections not only with clients, but also with each other. Each of them receives the signal from the other and transmits it further. However, this increase in range comes at the cost of another set of hardware for the access point. The next disadvantage: the access point must provide simultaneous connection to both the network and the client - this reduces efficiency by half. Another, less expensive, but often quite effective way To cope with the problem - replace the included antenna of the router with one that has a higher gain or even a directional one.
Wi-Fi Router or Wi-Fi access point loses connection. The network is functioning normally, but the connection is constantly being lost. The problem is most likely in the poor quality of the electrical network. Even a small voltage drop is enough for the router to lose connection. Solution: purchase a small uninterruptible power supply and connect the router through it. If this happens rarely, most users turn the device off/on, but this is not the solution.
Breaks wi-fi connection connections. When the wi-fi router and computer adapter are made by different manufacturers, this can cause some problems. As a rule, updating helps here software. Find a supplier on the website latest version and install it through the configuration menu. Especially often this problem can be solved by updating the firmware on D-Link access points and routers.
Common mistakes and setting up a Wi-Fi router
Incorrect IP configuration. In order for two network communication components to exchange files, each needs its own IP address. This network data is distributed by the DHCP (Dynamic Host Configuration Protocol) server in the router (don’t forget to check in the router’s web interface that the DHCP server is enabled). Open Control Panel and select Internet Connection. Select “Settings” from the WLAN connection menu. Next, double-click on “Internet Protocol” (TCP/IP) and activate the “Obtain an IP address automatically” option. Confirm by double-clicking “OK”. If you have several devices that can be DHCP servers, a conflict may arise between them. This leads to real chaos. To track which device is causing problems, use the DHCP Find app. It reports the MAC addresses of the DHCP server. MAC addresses are usually written on the bottom of devices. This way, you can quickly identify the troublemaker and disable their DHCP server. If communication is still not working, your browser's proxy settings may be to blame. Set up your browser: in Internet Explorer click on “Service | Internet Options" and go to "Connections". In the “LAN Settings” section, uncheck all the boxes, including “ Automatic detection parameters". In other browsers, such as Firefox, Chrome or Opera, these functions have similar names.
Programs for setting up and optimizing Wi-Fi networks (WLAN)
DHCPFind — looking for WLAN troublemakers
PuTTY — configures WLAN routers
EasyWi— FiRadar — displays all WLAN connections in the area
Wireshark — finds unprotected data
NetworkShareBrowser — shows all free networks
Wlandscape — creates a WLAN coverage map
Wi fi router Netgear WNR3500L. Easy setup
Using the Chekhov.NET provider as an example
- We connect the cable from the provider to the router (the WAN port is yellow).
- We take another cable (crimped on both sides twisted pair). We connect one end of the cable to the router (LAN port - orange) and the other to the computer.
- We connect the router to an outlet. Let's turn it on.
- Insert the disk from the kit into the drive (Russian interface). Set up step by step. Everything is very clear.
- Next, watch the video (below) and set up a PPPoE connection: go to the web interface - www.routerlogin.net with the admin | password, select the connection type - PPPoE, set the login and password from the contract, IP automatically, change the password to access the router. Apply the settings, reboot - done!
9HQhe6H92iU
How to set up a NETGEAR JWNR2000 Wi-Fi router with a PPPoE connection
Go to the Internet Explorer, Mozilla, Opera, Safari browser and type 192.168.0.1 in the address bar. In the window that appears, enter admin in the “Username” field, enter password in the “Password” field and click the “Ok” button.
After this procedure, the router menu will appear:
Setting up a PPPoE connection
Click the "Ok" button in Fig. higher. “Basic settings” will appear (in the menu on the left it is: Installation - Basic settings).
To the question “Do I need to enter connection information when connecting to the Internet?” We answer “Yes”:
In “Internet Service Provider” select “Others” (which corresponds to the PPPoE connection type):
Connection mode – connection setup mode. "Always on" for a permanent connection. “Connection on demand” - establishing a connection when necessary - that is, when traffic directed to the Internet appears, the device will establish a connection, and if there is no activity for more than the time specified in “Inactivity time before disconnecting (in minutes)”, it will disconnect. If you select “Connect manually”, the connection is established and terminated manually
“Internet IP address” leave “Obtain dynamically from Internet service provider” , if the IP is not issued to you by your provider (static) , as well as other parameters (everything must be in the contract):
DNS server addresses can be specified manually, if available from your provider, or you can receive them automatically:
Main DNS: xxx.xxx.xx.x
Additional DNS: xxx.xxx.xx.x
Leave the “router MAC address” as default:
Setting up Wi-Fi and security using an encryption key
Setting up Wi-Fi network security using MAC address filtering
Setting up a Netgear WG602 access point
Settings wi-fi points Netgear WG602 access is quite simple . Before starting the connection, hold down the “Reset” button, which is located on the back wall of the access point for 20 seconds to reset all settings to standard. Remember that if you are using an Internet connection via a login-password pair, then you need an access point that supports the PPPoE protocol, the connection of which is described above; the Netgear WG602 access point cannot be used with this type of Internet connection.
We connect the Netgear wg602 access point to the computer’s network card using twisted pair cable. In the connection settings of the network adapter (card) of the computer we set IP 192.168.0.2, mask 255.255.255.0, deleting the previous settings if they existed there, but you can also use a second network card on motherboard to configure the access point.
Open a browser to connect to the web interface of the access point, write 192.168.0.227 in the address bar, a dialog box should appear where you need to enter login: admin password: password (these settings are written on the bottom cover of your access point)
Go to the Wireless Settings menu, enter an arbitrary network name - Wireless Network Name (SSID) and region (Country/Region), click "Apply".
Now we need to go to IP settings and “drive in” the provider’s settings from the contract, unchecking DHCP. This checkbox will not need to be unchecked only for those whose provider assigns an IP automatically or you use a wired router (switch) with an IP assigned to it. Such routers are necessary to connect several devices in an apartment. Leave all other settings as default.
Reboot the access point (go to the Reboot AP menu section), remove the cable from the computer’s network card:
1) If you have an Internet cable connected to the above-mentioned switch with an assigned IP provider, then insert the end of the cable that you pulled out of the computer into the switch and connect to the newly created Wi-Fi network using any device that supports this technology wireless communication by entering only a password (for example, a smartphone). Skip this paragraph if you are not using such a router.
2) If you only have a cable from the provider in your apartment (house, office), then remove the end of the cable pulled out of the computer from the access point and connect the Internet provider cable to it. Check network functionality.